Desktop intercom system professional#

To make setup of the unit easy and intuitive a display is provided on the front panels. As well as flashing a LED at the receiving end of the call an audible вЂbeepвЂ™ can be set to alert the user that an incoming call has been placed to them.

To call another user the operator double taps the speak key of the channel they want to call, this then flashes a bright yellow call LED on the other users keypanel, which continues to flash until the call is answered. The microphone input on this headset connector is in parallel with the 3 pin XLR and the headphone output is in parallel with the 6.35mm TRS jack.ДЄ 4 pin male XLR can be fitted to special order instead of the 5 pin female headset connector.ДЄ simple call function is inbuilt allowing the operator of one unit to call/alert other users that they want to communicate with them. If you prefer an intercom headset with a single XLR connector for microphone and headphones then fitted as standard to the rear is a 5 pin female XLR headset connector. Headphone connection is via a standard 6.35mm TRS jack socket located out the way on the rear panel. The unique headphone amplifier can also drive mono earpieces from its stereo output without any performance issues. The headphone amplifier is stereo and sources can be panned to left or right ears as desired. One of our unique headphone amplifiers are fitted to the Beatrice D4, these allow either low or high impedance headphones to be used and automatically adjust the output level to match the impedance of headphones in use. It can also be powered via the Ethernet cable by standard PoE (Power over Ethernet), which can be supplied by an external PoE switch or a midspan power injector. It is terminated with a standard IEC plug, making it easy to plug in wherever you are in the World. This multifunctional control provides day to day operational control of:ДЄ)В Overall volume control (just turn the knob)Д«)В Incoming channel level (push the speak key and turn the knob simultaneously)Д¬)В Panning (push the speak key and push and turn the knob simultaneously)ДЄn inbuilt wide range switch mode mains power supply is fitted for powering the Beatrice D4. The front panel features an easy to use volume/ setup control. WhatвЂ™s the point of an intercom unit if the onboard speaker is so small and cheap that you canвЂ™t understand what is being said to you? We use high output, high quality, large magnet Visatron speakers with excellent voice intelligibility to make communication straightforward and easy to understand. Twelve Volt Phantom power is also available and can be turned on/ off as required.

This microphone amp has two microphone sources, either the inbuilt front panel mounted electret capsule which provides good voice intelligibility from normal working distances or a balanced XLR input for connecting external gooseneck microphones to.

An inbuilt partyline facility allows any of the 4 incoming circuits to be routed to any of the 4 output circuits making both simple partyline and more complex group circuits easily configured.ДЄ good quality, clear sounding microphone amplifier designed for communication purposes is fitted which also has the benefit of a compressor/ limiter circuit to help keep levels and intelligibility consistent even when the operator gets overly excited. PLEASE NOTE THERE IS A LIMITATION TO INCOMING NETWORK STREAMS SEE вЂ*вЂ™ДЄudio routing to/ from other devices is setup using Dante controller which allows for point to multipoint routing on outgoing circuits (but only 1 single incoming circuit for each of the 4 channels).

Depending upon how the Dante network has been routed the incoming audio circuits and outgoing circuits can be different locations. One single user connected to the unit can listen and communicate with 4* separate locations on the network. It includes all the basic functionality required for small intercom systems and none of the overly complex installation requirements normally associated with large systems. This small desktop unit was deigned to be very easy to use for the operator and simple to setup for the technician. The Glensound Beatrice D4 is also AES67 compliant. As such the BEATRICE D4 is also fully compatible with other manufacturersвЂ™ equipment using the Dante protocol. It is part of our Glensound Beatrice intercom system that utilises the reliable and proven Dante network audio transmission protocol to allow real time distribution of uncompressed audio across standard networks.

Desktop intercom system professional#

The Glensound BEATRICE D4 is a robust, 4* channel Desktop intercom with crystal clear audio designed for broadcast, theatre and professional audio applications.